I have several of these in different locations (separate, identical V3 hubs). They are all identical and all use the same Zooz driver and they work fine. BUT… Even though history shows no motion for a long time in the past, one of them retains the little red motion indicators on the tile. Not re…

Well - looks like it was just a dropped “inactive” message. As soon as motion was triggered, it began reporting correctly again! (Somehow it just didn’t occur to me that a single message could be dropped!)

[image] art_333: They are all identical and all use the same Zooz driver and they work fine. What model sensor? Model numbers are important. Which driver? The official Zooz Multisensor driver? If you trigger motion on the sensor in question, and then let it go back to no motion, will t…

Yeah. ZSE40 VER 2.0. Standard (official) Zooz Multisensor driver. Don’t know about triggering it; right now it’s about 1000 miles away from where I am… (But that was going to be my next test when I get back there!)

Few possibilities: The “no motion” message was lost. If for some reason that message didn’t make it, theres nothing but the simple retry that Zwave has to try and get it there. Theres no application retry or “refresh the state every XX minutes/hours” if no further activity occured. The hub ma…

ST is getting temp, humidity, and lux reports as expected. Probably just a dropped message. It’s certainly not a big deal - just something I’d never seen before! Thanks for your response - it’s pretty much what I was thinking…

Interesting! Thanks for mentioning this, @art_333 . I’m experiencing the same issue: two ZSE40 devices, powered with a voltage regulator fed by a typical USB charger block, both have showed ‘motion’ when there wasn’t anyone home, and both were switched from the Zooz driver to the more generic SmartTh…

[image] Barkis: Years ago, as an experiment describe here , I forced a sleepy contact sensor on a door 1500 miles away to report it’s open/closed status the next time it woke to report battery level. The door was closed–not open, as SmartThings was reporting! The Zwave Sensor CS driver will do…

Will this nonsense ever stop? who cares about matter, thread border s2 . will it ever work as used to? when Kevin’s handlers will be implemented? These edge devs must have some mental issues, announcing new icon or BS map view as breakthrough feature?

[image] nothingworks: who cares about matter, thread border s2 . Fair enough, I have moved the detailed S2 discussion to its own topic. The main point here is that the ZSE40 does support S2 authenticated security, so if you have it paired that way it should theoretically be less likely to lo…

[image] nothingworks: These edge devs must have some mental issues, announcing new icon or BS map view as breakthrough feature? In all fairness, the “Edge devs” you speak of may be divided into two categories: volunteer coders from the SmartThings Community and Samsung employees tasked with…

Strange (minor) Issue with Zooz ZSE40 4-in-1 Sensor

General Discussion

csstup (Corey Stup) April 21, 2024, 6:21pm 7

The Zwave Sensor CS driver will do something similar. On WAKEUP, if the hub thinks the device is currently showing motion as triggered, it will request its current status. It supports the ZSE40 if you’d like to try it.

Topic		Replies	Views
Zooz Z-Wave Plus S2 Outdoor Motion Sensor ZSE29 Devices & Integrations	3	411	January 1, 2023
Zooz outdoor motion sensor issues Devices & Integrations	21	746	June 10, 2024
ZOOZ ZSE40 4-in-1 sensor Goes Inactive Devices & Integrations	2	813	November 7, 2017
[RELEASE] Zooz Outdoor Motion Sensor - VER 2.0 (ZSE29) Community Created Drivers dth_motionsensor , dth_luxsensor , dth_security , dth_sensors	33	3048	December 18, 2022
Zooz ZSE40 4-1 Motion Sensor and other Zooz devices (ZSE01, ZSE02) Connected Things dth_motionsensor , dth_security , dth_sensors	219	36065	August 8, 2019

Strange (minor) Issue with Zooz ZSE40 4-in-1 Sensor

Related topics