Has anyone had issues getting their GD00z to open and close their garage door? I have a new chain driven Chamberlin opener that will not respond to the gd00z. It is not a MyQ opener and is not on the list of incompatible devices. It is just a plain no frills opener. Any thoughts? I can’t get it t…

My genie required a dry contact adapter, about 20 dollars. The linear is just like a relay the smart openers require their specific interface type. For me the dry contact made for my genie intellicode fixed it with connecting it inline

What happens when you try? Does the controller beep and flash? Did you double check all of the connections between GoControl and opener? Did you try removing power from both then synchronizing again?

The controller beeps like it’s going to open, then tries to open the door (at least on the app it says opening). But the door doesn’t go up. All the connections are solid. I redid them multiple times. Also tried unplugging the door opener and controller. Then plug in the opener, then the control…

That’s odd, if its wired correctly with the wires going into same connections as push button it should work, and sounds like it is. I know it sounds dumb but the tilt sensor arrow is pointed up right? I had problem with mine initially and how I solved it was stripping wire off a little bit more th…

Yea I wrapped the wires together and the tilt sensor is working. I also had issues with my other relay I had attached to my old opener. It’s a zwave relay but it wouldn’t trigger the door to open either. I’m not sure but I read that maybe Chamberlin models are encoded signals that change on a re…

Have you seen this thread? [image] Linear GD00Z (Garage Controller) and Wall Switch (with Motion Detector) Devices & Integrations Thanks for the post guys! I thought I had a bad GDOOZ until I read this post. Has anyone had any success with this issue? I have a Liftmaster…

All the GD00Z is doing is acting like another push button but like in the thread @Danabw shared other things can be going on. Make sure you are waiting full minute after you send command , the controller knows if it didn’t open and will try again after x number of seconds. Also could have an issue…

sounds like a wild goose chase in progress. For Chamberlain HD210, the wall-remote-button does not appear to be a simple dry-contact button, based on the installation instructions that say the button “synchronizes” with the motor-unit. You’ll probably need to solder the GD00z output to the wall b…

Ok, so I finally got it working. Like others have said the Chamberliain openers use encrypted signals to open and close the door. So I ended up soldering a new wire to the push button switch and running that to the gocontrol controller. So the controller is wired directly to the push button switch…

New here and pretty new to zwave in general. Just got the GD00z. I got it connected to my network. Same as the rest. The device beeps like it’s going to close but doesn’t work. It’s a Chamberlain opener. I have it wired to the same terminals as the wall switch. But it will not work I’m thinking this…

Linear GD00z-4 chamberlain HD210

Devices & Integrations

AnthonyS August 12, 2017, 3:22pm 12

Here is a picture of the liftmaster series 1300. I had it connected to the two left terminals which by the instructions are the same terminals that the wall button is connected to.

Topic		Replies	Views
GD00Z-2 not opening Chamberlain Model: LW2200 garage opener General Discussion uncategorized	11	4040	May 1, 2017
Linear GD00Z (Garage Controller) and Wall Switch (with Motion Detector) Devices & Integrations	108	39838	June 21, 2020
Go Control /linear gd00z4 contact not opening Connected Things	13	1848	July 22, 2021
GoControl/Linear Garage door Opener Devices & Integrations	9	1484	March 25, 2017
GD00Z-4 Garage opener doesn't work...sort of Devices & Integrations garagedooropener , gd00z-4 , lineargd00z , garage	6	4439	March 22, 2016

Linear GD00z-4 chamberlain HD210

Related topics