EDIT – As the vendor supplied Channel is now publicly available, my strong recommendation would be to use their channel if at all possible to achieve the best compatibility for supported devices. [image] [ST EDGE] [RELEASE] Homeseer Devices, manufacturer-provided edge driver…

Hi @jshessen My wd100 dimer have a problem. It working the first time after that it’s getting out of sync. If I switch it on , the light goes on and in the app it stays off ,after that it won’t respond . Thank you

I have a HS-WX300 switch configured as a switch (rather than a dimmer). I recently converted it to the Edge driver but now can’t control the status LEDs :frowning:

@blanalex – Unfortunately, this is the position many of us have found ourselves in. I am working to recover all of the vendor specific capabilities for these switches (first) and even to push on to the fan controller and/or flood light as I can. As I mentioned above, I need to sort out some parame…

Just an FYI, I have pushed another release this evening to resolve the 300 series settings/parameters smartthings edge:drivers:install -C c408fa0b-438f-4d00-bf36-efe7343c66b7 5f2d5dca-fcd9-4895-805a-6e976dd349d1 [image] Release v0.2.1 · jshessen/SmartThingsEdgeDrivers 0.2.1 (2023-02-05…

@jshessen or @csstup are either of you still working towards a release of the driver for the HS-FLS100 floodlight?

[image] adfurgerson: are either of you still working towards a release of the driver for the HS-FLS100 floodlight? I am. [image] Homeseer HS-FLS100-G2 integration Devices & Integrations Anyone have experience integrating Homeseer HS-FLS100-G2 motion detector into s…

Progress – now I just need to sort out the automation commands to the individual LEDs [20230205_130137]

Hopefully this is welcome news. I have just pushed/released the next driver (0.3.0) which includes the ability to address the individual LEDs via a component. This means that functions such as Smart Lighting can be used directly manipulate the “On” or “Off” of the LED. Because these are defined a…

PS – I have tested the following scenarios: Use a WD100 Toggle up 2x to turn on a subset of LEDs (1,3,5,7) Use a WD100 Toggle down 2x to turn off all LEDs (1-7) Use a Open/Close door sensor to turn on an individual LED (2) on Open and turn back off on Close The current setup uses whatever “color”…

[image] csstup: [image] jsdray: I have an HSFLS100+ Flood Light Motion Sensor, [image] 5spot: I would also love to see an edge driver developed for the FLS100+ Motion Sensor @Rodd62 and I are testing my driver for the FLS100+, both the original and the 2020 G2 variant. Should be av…

[BETA] Edge Drivers for Homeseer Devices

Devices & Integrations Community Created Drivers

csstup (Corey Stup) February 5, 2023, 12:05pm 36

I am.

Topic		Replies	Views
[ST EDGE] [RELEASE] Homeseer Devices, manufacturer-provided edge drivers Community Created Drivers edge_lighting , edge_sensors , edge_hvac	31	2871	January 11, 2024
Post Requests for Zwave Edge Drivers Here (community-created) Community Created Drivers edge-device , aftergroovy	849	76022	May 28, 2026
Hub Connected Devices Now Use Edge Drivers Announcements edge-device	229	31669	July 13, 2023
Preview \| SmartThings-managed Edge Device Drivers Devices & Integrations edge-device	273	66040	December 6, 2023
Post Requests for Zigbee Edge Drivers Here (community-created) Community Created Drivers aftergroovy	1559	48654	August 26, 2026

[BETA] Edge Drivers for Homeseer Devices

Related topics