Ah ok, thanks. I didn’t expect the UI to change like that between DH and Edge.
I just wanted to make sure I have plans set for the few devices I know will break when the end of life comes for groovy.
Edge support has come such a long way since I last was looking into it that more and more I was expecting to break are being supported.
I was surprised to see that there is still hope for Xiaomi sensors and the z-wave repeater inside of Iris plugs so along with your driver here, I may not actually have to get rid of or lose much by the end of things.
@JKB121 Your Z-wave device must already be using an Edge driver.
Subscribe the the channel (link in 1st post) and install this driver. In the app make a driver change.
I’ve been using this for various things - smoke, leak detectors, etc.
After many months, battery still hasn’t reported, and I get a “Couldn’t get devices status” error when opening (though the main function still reports properly). I think it’s because of the battery report.
I saw your recommendation from a post I made and tried using this driver.
Issue I have, once I switch to your driver, when I select “Smoke” - I loose connectivity to the device.
I have to fully delete and readd the device.
[EDIT]
I had a similar issue with a GE Motion Switch.
Then suddenly, without any explanation, the device was “connected”
I’ll keep testing this… Perhaps is a matter of rebooting or something else I need to explore deeper.
It sounds like most of the special options haven’t been initialized. If swiping down to refresh on the device detail screen in the app works (it often doesn’t) then doing that should help populate those. My own lock was often a bit finicky about responding to a full poll though, so it might take a few tries. Another option is to create a scene to change each of those options, which should result in each being populated and usable from device detail screen.
I’m now able to use the Schlage Lock Alarm, set to “Activity Mode”, to fire off the SmartThings Smart Home Security Monitor! Prior to your driver, it only worked when the Lock was Locked or Unlocked.
So is excluding and including the only option to get this driver working? I have enrolled in the channel and added the driver. But all my EcoLink Z-wave plus tilt sensors don’t have the “driver” option in the menu. If thats what I have to do then I will but wanted to make sure.
I’ve already gone through my IDE and deleted every custom DTH except for the single MyQ one, same for custom apps, so that should be clean.
Hi @philh30 ,
I use your Z-wave Masquerade v1.01 for Monoprice 24259 contact sensors. It works great but one weird issue is the Monoprice 24259 devices often showing offline but they are actually not offline. When I open/close the contact, it shows the correct status. Most time I open/close the contact, the offline text disappears. However, soon the text comes back again later.
@philh30
Thank you , this driver make 7 more devices for me .
Gocontrol door sensor and motion sensor.
Watercop valve that the status was invert with the smartthimgs driver.
More of an FYI… I was looking at your fingerprint for remotec-zfm80. I just see the switch options. There is also the ability to set a timeout (auto off). Here is the documentation for the relay…
Parameter 2 is timeout period 0-240 minutes default 0 - disabled
Parameter 3 is NodeID 1-232
Parameter 4 Set relay if timeout 0 = turn off/1 = turn on default 0
@philh30 , I use this driver for several Monoprice sensors and it works great. I have a request.
I use a sensor to monitor when my Security system is Armed or Disarmed. So, in the Alarm profile, is it possible to add two more selections for State 1 and State 2. The Selections I would like are “Armed” and “Disarmed”
By the way, all my devices have now been converted to Drivers, and for Z-Wave, 18 of 38 devices are using your drivers. Thank you very much.
The “alarm” profile in Masquerade is to mimic a Siren, not an alarm/security panel. The driver would have to be enhanced to simulate a securitySystem capability, or perhaps there is already a virtual securitySystem device that you can control with routines.
Tagging on to Corey… There’s a security system capability that has arm/disarm functions but last I checked it was broken. A custom capability would be required to have what you requested work properly.
I am getting a smoke and CO2 alarm from my Ecolink open/closed sensor driven by a Kidde smoke and CO2 interface to my wired alarms using Masquerade v1.01. Changing the invert status didn’t change the smoke alarms. Previously the Ecolinks reported open when not armed with the ZWave sensor driver. I’d like it to be treated as a smoke sensor in the Home Monitor.