Post Requests for Zwave Edge Drivers Here (community-created)

Devices & Integrations Community Created Device Types
,
1790

I need this too (heatit ztrm3 edge driver), or else i will soon need to find a different hub solution.

1791

Not even sure if possible but something to have the Neato Botvacs still accessible through ST would be great. I know you can use virtual switches to have Alexa turn it on but having it within ST and it knowing the state of the vacuum is great, particularly fur action tiles. Thanks

1 Like
1792

Hi @Belgarion
Added to this driver version

┌─────────────┬──────────────────────────────────────┐
│ Name        │ Z-Wave Switch Mc                     │
│ Version     │ 2022-09-18T11:36:42.766694342        │
└─────────────┴──────────────────────────────────────┘
  - id: 014F/4457/3034
    deviceLabel: Linear Dimmer
    manufacturerId: 0x014F
    productType: 0x4457
    productId: 0x3034
    deviceProfileName: switch-level
2 Likes
1793

SmartThings has a “Z-Wave Virtual Momentary Switch” driver available. Is it possible to add this device fingerprint to it:

Metrics * Received Messages From Device: 17

  • Received Messages From Device (Duplicates): 2
  • Messages Transmitted to Device: 14
  • Messages Transmitted to Device (Failures): 0
  • Updated Time: 2022-09-18 10:46 AM EDT
    Data * networkSecurityLevel: ZWAVE_LEGACY_NON_SECURE
  • productName: Remotec ZFM-80
  • manufacturer: Remotec Technology Ltd
    Raw Description zw:L type:1001 mfr:5254 prod:8000 model:0002 ver:1.01 zwv:3.40 lib:06 cc:20,25,27,72,86,70,85

This device currently uses the “Z-Wave Virtual Momentary Contact Switch” DTH.

1794

This thread is intended to request custom edge drivers from community developers. I’m not sure what the mechanism is for asking for changes to a production driver. :thinking:

I know some people have been asking in the official announcement thread, but I don’t know if they got any response.

1 Like
1795

We posted the driver today. Combo driver that contains support for the LS100+. Give it a try!

2 Likes
1796

Hello,
Which edge driver do I need to install for the “spring window fashions shade” DTH?
Thanks

1797

Z-Wave Window Treatment.

Currently the two devices from the DTH are only fingerprinted for the beta channel.

1798

Tested each sensor twice and each reported wet or dry. If anyone needs the Homeseer LS100+ manual here you go:

Thanks Corey/Phil for your time and help on the Homeseer leak sensor Edge driver.

3 Likes
1799

Note that the manual (both the v1 manual on the zwave alliance and the manual on HomeSeer’s site) has a bunch of errors for the actual behaviour of the LS100+.

The most notable are:
Secure Inclusion:
Press the button on the device once. The LED will flash indicating its starting secure inclusion.

Normal (insecure) inclusion:
Press and hold the button for 4.5 to 5 seconds. I count “one one thousand” while doing it, if you go too short it does a secure inclusion. If you go just over 5 seconds it does a reset or nothing. So release right on 5 seconds.

Exclusion:
Press the button 3 times quickly to exclude. The manual is correct.

2 Likes
1800

Does anyone need native support for the HomeSeer HS-MS100+ motion sensor? I can add that one to the TODO queue if needed.

1 Like
1801

The only two instructions I needed to use was the following:

Exclusion 1. Put your home automation controller into Z-Wave ‘exclusion’ mode. 2. Quickly triple-press the Z-Wave network button. Wait for the exclusion process to finish.

Secure Inclusion (recommended if your home controller supports “S0” or “S2” Z-Wave encryption) 1. Put your home controller into Z-Wave ‘inclusion’ mode. 2. Press and hold the Z-Wave network button for 5 seconds, then release it. Wait for the inclusion process to finish.

1802

I found this to be incorrect (after including/excluding the device 50 times during driver testing). If you press and hold for 4.5 - 5 seconds it will do an insecure inclusion. Pressing once (or not holding to 4.5 seconds) will get you secure S2 inclusion. Check your actual inclusion level with the CLI:
smartthings devices <num> -y
if you’re curious. This also may be firmware dependent, but all my LS100’s (12+ in use) are the same, V1.04.

1 Like
1803

Hello, can you add this fingerprint to Edge driver Z-wave sensor?

fingerprint mfr: "0154", prod: "0004", model: "0007", deviceJoinName: "POPP Open/Closed Sensor" //EU //POPP Door Window Sensor

1804

@Mariano_Colmenarejo
This worked perfectly… thank you very much!! :heart_hands: :+1: :100:

2 Likes
1805

Is there an edge driver that would work with the GoControl Multifunction Siren? The stock Z wave siren device handler doesn’t control the strobe.
I am currently using this custom device handler: [OBSOLETE] GoControl Siren / Linear Siren / Vision Siren. The Raw Description is: zw:F type:1000 mfr:014F prod:2005 model:0503 ver:1.65 zwv:3.42 lib:06 cc:25,80,70,72,86
Any help would be appreciated, Thank you

1806

@Mariano_Colmenarejo can you add the fingerprint for the Intermatic CA3650 to your Z-wave Switch Mc driver?

raw description:
zw:L type:1001 mfr:0005 prod:4341 model:3750 ver:1.101 zwv:2.09 lib:06 cc:91,73,72,86,60,25,27

Thanks!

1807

Can you add driver for Leviton switch
MSR: 001D-1706-0334
manufacturer: Leviton

mfr:001D
prod:1706
model:0334

1808

Need driver for Leviton Switch

mfr: 001D
prod: 3201
model: 0001
manufacturer: Leviton

1809

These should both be joinable as generic switch devices from the Beta Edge Zwave Switch driver.

1 Like