NOTE: If the profile changes are not applied well on already installed bulbs, you may have to uninstall the bulb in the app and then press + and search nearby to reinstall it.
I just got updated driver on hub. I had to remove/add bulb again.
So far everything works. No issues with Temperature Level (2700-6500K) or Dimmer.
Thank you.
Now itâs time to add driver to all other lights and modify Automations.
One note to everyone, place dummy device (virtual switch) in each Automation, prior to removing Groovy device, as you will probably loose those automations when devices are deleted. Dummy device will have app keep Automations, and when you add Edge device, add them back to automation, and remove dummy.
New Edge Driver for SmartThings Zigbee Motion Sensor GP-U999SJVLBEA:
SmartThings Motion Sensor manufactured by Samjin. It worked with the DTH SmartSense Motion Sensor.
Add in preferences the Temperature Reports Settings to customize temperature precision and to optimize battery consumption.
Maximum interval Temperature report: Adjustable between 5 and 240 min.
Reportable Temperature Change: Adjustable between 1Âș and 6Âș
This sensor could have been added to the zigbee motion Driver, but for the temperature report settings to work I would have to also modify the Motion Sensor IRIS model 1117-S sensor and I have not one to test.
I will post it tomorrow on the channel and update the list of drivers
Hi Mariano,
I am new here. In fact, this is my first post. I have enrolled to your Edge Channel. I just wanted to check if itâs possible for you to help add the Zemismart Push Zigbee Switch in the Zigbee switch list.
@milandjurovic71, I have published a âZigbee Level ColorTemperature Lightâ drive so that you can test how the driver change works in the App.
-This driver is the same as the âZigbee Level ColorTemperature Bulbâ, but has no settings for Progressive Turn ON-OFF.
Changing the driver usually works fine, but sometimes it gives ânetwork errorâ. Ignore it and donât click on using this driver again.
Go back leaving the details view, wait about 15 sec and go back into the details view and verify the driver you have installed. 90% of the cases I have installed it well.
If the driver has not changed, make the change again.
Thedriver change process is sometimes a bit slower and some times out and the error pops up. In the logcat you can see that the change is in process.
@nayelyz, Perhaps this response waiting time should be extended since if you insist on reloading the same driver it can give problems, since it tries to do a lifecycle removed from the driver in which it is no longer and a new installation of the driver that may be in installation process.
I put a link to two videos, one with the change driver error, but well done and another working fine
Ok, actually, we have noticed that trying to change between drivers that donât have the same configuration in the device profile causes the issue. I already reported it, the engineering team will decide the next steps regarding this tool and the displayed errors.
So, please consider this when you change the driver through the app. In that case, it would be easier to re-install the device.
@nayelyz and @Mariano_Colmenarejo i have successfully swapped drivers both ways without to much issues, besides Network error that went away.
Anyway, issue with Temperature jumps still exist .
Maybe engineers need to look at Zigbee libraries
Thank you for this verification @Mariano_Colmenarejo and @milandjurovic71.
I already reported the issue with the info that Mariano provided, so, Iâll let you know the feedback of the engineering team.
New version 2.0 of the Edge Driver âZigbee Motion Sensorâ:
Added:
Version Info in preferences: Version 2.0 (Oct 2021)
Added: ST Motion Sensor (Samjin) with settings for temperature reports
Modified Iris Multiporpuse Sensor for settings of temperature reports.
If you have installed ST sensors with the âST Motion Sensorâ Driver and others with âZigbee Motion Sensorâ you can change your ST sensors to the âZegbee Motion Sensorâ driver with the Change Driver tool in the Driver menu of the HUB and thus have installed only one Driver.
The MultiPurpose Iris Sensor is untested, in case anyone wants to give it a try.
The problem is that by reinstalling the device you lose all the automations or you have to modify them.
If this device is a repeater and he has devices on his mesh, you take them offline until the mesh is rebuilt.
As recommended @erickv, we have to be patient and allow time for the changes be executed.
And increasing the timeout that generates the error might help