(EDGE Driver-Mc): Zigbee Drivers for Motion, Open/Close, Moisture, Smoke-Co Sensors and others Devices

[Mariano_Colmenarejo]

@MattP

If you want you can delete the logs to clean up a bit, hahaha

[MattP (Matthew Park)]

done. I’ll take a look at adding other devices tomorrow. Thanks again.

[gifa84]

Hi @Mariano_Colmenarejo ,

I tried to install this zigbee power meter using your zigbee Power/Meter MC but it is not regnognized.

Can it be compatible?
Thanks

[Mariano_Colmenarejo]

@gifa84

Can it be compatible?

Hi @gifa84

This device uses the EF00 cluster and is not compatible

[gifa84]

Thanks @Mariano_Colmenarejo,

so there is no way I can use it with smartthings?

[Mariano_Colmenarejo]

@gifa84

so there is no way I can use it with smartthings?

Ask in this specific thread of the EF00 cluster

[ST Edge] Personal Tuya Devices - Generic EF00 Device

Just to let people know that I just published in my public channel a very simple and generic way to integrate devices that works with 0xEF00 tuya cluster. It requires a little intuitive skills because the driver exposes a way to control tuya datapoints directly. Features: Support to some stock capabilities switch switchLevel button contactSensor doorControl illuminanceMeasurement motionSensor presenceSensor relativeHumidityMeasurement temperatureMeasurement valve waterSensor / leakSensor Support to generic tuya data types boolean enumeration value string bitmap raw Known limitations Can’t have 2+ components referencing the same datapoint This is how your device will be detected if there isn’t any predefined datapoints mapped in the code. [detailView_1] This is how your dev…

[Wajo357 (Joey W.)]

@Mariano_Colmenarejo,
Is there any chance we can get LQI and RSSI info for the zigbee window treatment driver? Thanks!

[Mariano_Colmenarejo]

@Wajo357

Is there any chance we can get LQI and RSSI info for the zigbee window treatment driver?

I will look at it.
Next week I won’t be able to do anything, remind me if you see that I don’t answer the following week

[Wajo357 (Joey W.)]

Thanks! Will do!

[Tamerfakhry]

Hi there,

Would be able to add the finger print to this sensor?
Centralite Micro Door and Window Sensor
I can give you the device ID, if you are able to.

[Mariano_Colmenarejo]

Hi @Tamerfakhry

If you tell me the information of the fingerprints I could see it

[Mariano_Colmenarejo]

@3asmarthome

• manufacturer: Feibit Inc. Co.
• model: FB56+ZSW1JK2.5

Hi @3asmarthome

sorry, i forgot this.
I won’t be able to do it for a few days, I don’t have access to the cli.

[3asmarthome]

Thanks for your reply. It is fine to do it when you are convenient.

[AverageQuizzer (Dominik Manser)]

I tried to add my Lidl doorbell, but it didn’t find a driver. Is it possible to add it?

[SivaG]

Thanks @Mariano, Successfully added all devices and made them working with google. Thanks a lot for your help all through the way. Much appreciated.

[Sundareshwar (Sundareshwar Mathiyalagan)]

@Mariano_Colmenarejo Hi Mate,

I am still facing the same issue with contact sensor going to offline. Its happening for SONOFF and SAMOTECH contact sensors. Its became active when there is event occurs otherwise it goes to offline.

My hub firware has been updated to 46…

Please find the device offline screenshot.

[Mariano_Colmenarejo]

@AverageQuizzer

I tried to add my Lidl doorbell, but it didn’t find a driver. Is it possible to add it?

Hi @AverageQuizzer

I have not driver for Buttons, Maybe @erickv can add it to his driver

[Mariano_Colmenarejo]

Hi @Sundareshwar

I can’t think of what might be happening to make them disconnect.

Did you re-pair them with the hub on the new firmware?

[Sundareshwar (Sundareshwar Mathiyalagan)]

Not yet…need to check. Will try and get back to you with updated status.

[AverageQuizzer (Dominik Manser)]

@Mariano_Colmenarejo

Hi @AverageQuizzer

I have not driver for Buttons, Maybe @erickv can add it to his driver

That would be great. My other question is: For example the motion sensor from lidl has a driver, I was able to connect it and it works in the smart things app, but when I try it to link to google home, it doesn’t recognize the device and does not link it. Do you know if it should work, or is it only working with SmartThings?