I have zigbee thermostats from Sinope (model TH1123ZB-TH1124ZB). One my thermostat is now on the official zigbee thermostat edge driver (but not the others). The driver work really fine but with the update, we lost some features. First feature, is the outside temperature shown on the display of the thermostat. I know that to get the temperature, the thermostat must contact a web service so it’s not really a local feature.
Second feature, is the display of the time on the thermostats. I don’t know why the feature disappear because time is suppose to be a local value on the hub. It’s really pratical to have the time on the thermostat
So if it’s possible to do something about that it would be appreciate.
There is the raw discription for both model:
TH1123ZB: 01 0104 0301 01 0B 0000 0003 0004 0005 0201 0204 0402 0702 0B04 0B05 FF01 03 000A FF01 0019
TH1124ZB: 01 0104 0301 00 0A 0000 0003 0004 0005 0201 0204 0402 0B04 0B05 FF01 02 FF01 0019
There is the DTH code from the thermostats (if the can help you):
It has been misbehaving for the last several hub firmware updates, and decided to try an force the migration to an edge driver assuming I could use either a generic or GE-based default driver to get it to be stable. Neither has been true.
I have the Aeotec V3 hub. I deleted the device and have made multiple (10+, more?) attempts to add it and it appears as a “Z-Wave Controller Device” each time, although it is a zig bee device!
I have tried numerous troubleshooting steps (restarting hub, clearing unused drivers, etc,) but it does not register correctly. I assume that there is either some other problem present with my system (hub/device/other), but that if there is a correct edge driver available it should work - ?
Any help to locate or create the appropriate edge driver for the Outlink would be highly appreciated.
In addition to this device I have eight others (GoControl contact/motion/siren & Wink/Quirky Trippers) on DTH’s that I am also not able to locate edge drivers for, and I am hoping that they will be automatically, successfully migrated, but have low hopes if that actually occuring.
Just wondering @Mariano_Colmenarejo if its at all possible to have a driver for Aqara Temperature/humidity sensor without the thermostat stuff?
I had 1 Aqara sensor using the driver “Zigbee Temp Humidity Sensor MC-(OLD)” which i loved the tiles layout, but all my newly added sensors only have the “Zigbee Temp Sensor with Thermostat Mc” available, this one’s tile layout isnt as good and or useful.
Totally understand if this isnt possible.
@Mariano_Colmenarejo I dont have a option to create without thermostats, I’ve added the sensor by searching for device in Smartthings and it chooses the edge driver.
If i goto select different drivers, i have these :
@Mariano_Colmenarejo Thank you for everything you have done to support the ST community! I had preveously enrolled in your “Mariano Shared Beta Driver” channel on my hub for a couple of other devices, including the “Zigbee Switch Mc” driver. But it did not allow me to enroll my Outlink. That is we I made my post.
Shortly after you sent your message I deleted and attempted to reenroll the Outlink, but had the same outcome - It onboards as a “Z-Wave Controller” apparently using a Groovy DTH, as no “Driver” option appears in the device menu option.
I understand that changes to drivers can take up to 12 hrs, and so I waited overnight to reattempt to delete and add the device, but still the same result. Below is the “Zigbee Switch Mc” driver information as of right now -
Added 2 gang switch to this driver version
If you send the fingerprints for other 1 and 3 gang switch then I will add
Name Zigbee Multi Switch and Child Mc
- id: "TS0002/_TZ3000_ptjcjise"
deviceLabel: Two Switch