# Zigbee devices acting up

**URL:** <https://community.smartthings.com/t/zigbee-devices-acting-up/39411>\
**Category:** General Discussion\
**Tags:** zigbee, hubv2\
**Created:** [February 16, 2016, 6:46pm UTC](https://community.smartthings.com/t/zigbee-devices-acting-up/39411 "2016-02-16T18:46:02Z")\
**Posts on this page:** 8\
**Page:** 1

<div class="post-metadata">

**Author:** ![mterrace](https://yyz2.discourse-cdn.com/smartthings/user_avatar/community.smartthings.com/mterrace/32/26511_2.png) [@mterrace](https://community.smartthings.com/u/mterrace)\
**Post date:** [February 16, 2016, 6:46pm UTC](https://community.smartthings.com/t/zigbee-devices-acting-up/39411/1 "2016-02-16T18:46:02Z")

</div>

For the last two days I have been having major problems with my Samsung Motion Sensors (3 of them) and my Cree lightbulbs…my motions are not sensing motion (one of them is stuck in Motion) - I also have not been able to add a new Cree bulb into my ST? I have a ST v2 Hub, 40+ devices (Z-Wave switches and motions are working normally)…it wasn’t until I tried adding the Cree bulbs last night that I think it has something to do with Zigbee…Is it possible that this is ST platform (cloud) related?

I have a total of 8 Zigbee devices, and they are all acting up - all of a sudden…

I have rebooted the hub, with no effect.

Any help, is much appreciated.

Mark

---

<div class="post-metadata">

**Author:** ![JDRoberts](https://yyz2.discourse-cdn.com/smartthings/user_avatar/community.smartthings.com/jdroberts/32/56577_2.png) [@JDRoberts](https://community.smartthings.com/u/JDRoberts)\
**Post date:** [February 16, 2016, 6:58pm UTC](https://community.smartthings.com/t/zigbee-devices-acting-up/39411/2 "2016-02-16T18:58:07Z")

</div>

For Zigbee, you need to take the hub off power (including removing its batteries) for at least 15 minutes. Then when you power it up again it should rebuild all the address tables and re establish contact with all Zigbee devices. Just a reboot won’t do it, you have to keep the hub unavailable for long enough that all the devices go into “panic mode” so they’ll resynch when the hub becomes available again.

---

<div class="post-metadata">

**Author:** ![RudiP](https://avatars.discourse-cdn.com/v4/letter/r/a698b9/32.png) [@RudiP](https://community.smartthings.com/u/RudiP)\
**Post date:** [February 16, 2016, 7:09pm UTC](https://community.smartthings.com/t/zigbee-devices-acting-up/39411/3 "2016-02-16T19:09:22Z")

</div>

I had the same issue a couple of months ago and I had to move the ST Hub away from the WiFi router (at least 6 feet) and also had to change WiFi 2.4GHz channel until all ZigBee devices went back to normal. Good luck.

---

<div class="post-metadata">

**Author:** ![mterrace](https://yyz2.discourse-cdn.com/smartthings/user_avatar/community.smartthings.com/mterrace/32/26511_2.png) [@mterrace](https://community.smartthings.com/u/mterrace)\
**Post date:** [February 16, 2016, 9:16pm UTC](https://community.smartthings.com/t/zigbee-devices-acting-up/39411/4 "2016-02-16T21:16:57Z")

</div>

Thanks - I’ll try powering it down for 15 minutes first…

It is right next to my router too…hope that’s not it ☹

Mark

---

<div class="post-metadata">

**Author:** ![ashutosh1982](https://yyz2.discourse-cdn.com/smartthings/user_avatar/community.smartthings.com/ashutosh1982/32/15210_2.png) [@ashutosh1982](https://community.smartthings.com/u/ashutosh1982)\
**Post date:** [February 17, 2016, 5:00pm UTC](https://community.smartthings.com/t/zigbee-devices-acting-up/39411/5 "2016-02-17T17:00:48Z")

</div>

> [@mterrace](#):
>
> It is right next to my router too…hope that’s not it

That could also cause issues. Try to see if you can move the hub atleast 3-4 meters away from the router, by using an extended ethernet cable. Do you know if your WifI router chooses radio channels automatically?

---

<div class="post-metadata">

**Author:** ![mterrace](https://yyz2.discourse-cdn.com/smartthings/user_avatar/community.smartthings.com/mterrace/32/26511_2.png) [@mterrace](https://community.smartthings.com/u/mterrace)\
**Post date:** [February 17, 2016, 6:07pm UTC](https://community.smartthings.com/t/zigbee-devices-acting-up/39411/6 "2016-02-17T18:07:12Z")

</div>

That’s the next thing I am going to try - I may just move the hub upstairs to see if it works better…the power down for 15 minutes did not change anything – is there a way to tell if the devices go into panic mode?

Yes it changes channels automatically – is there a better channel to use for WiFi?

Thanks,

Mark

---

<div class="post-metadata">

**Author:** ![joelde](https://yyz2.discourse-cdn.com/smartthings/user_avatar/community.smartthings.com/joelde/32/203184_2.png) [@joelde](https://community.smartthings.com/u/joelde)\
**Post date:** [February 18, 2016, 6:15am UTC](https://community.smartthings.com/t/zigbee-devices-acting-up/39411/7 "2016-02-18T06:15:37Z")

</div>

how’d ya go? I had the same trouble… but now cannot re add any of my motion sensors. Have completely turned off wifi radio also… no go. ☹

---

<div class="post-metadata">

**Author:** ![mterrace](https://yyz2.discourse-cdn.com/smartthings/user_avatar/community.smartthings.com/mterrace/32/26511_2.png) [@mterrace](https://community.smartthings.com/u/mterrace)\
**Post date:** [February 18, 2016, 10:24am UTC](https://community.smartthings.com/t/zigbee-devices-acting-up/39411/8 "2016-02-18T10:24:38Z")

</div>

I moved the hub upstairs away from everything, and even closer to the sensors/bulbs. I powered down the hub for 20 minutes…and when it came back, the ZigBee motion sensors still did not work.

However, I was able to add a new bulb…but I had to be a few feet away from the hub when I added it…I read somewhere that ZigBee sometimes has difficulty adding into the system from a distance. After I added a couple of bulbs (Cree and Osram), I tried bringing one of the motion sensors that was not working, closer to the hub and pulled the battery and let it restart (I did not exclude/re-include it…just pulled battery and put it back in)…then it started working normally…so I did this with the other three sensors and they are all working now (knock on wood).

Mark
