Yes, you can trigger the emergency heat using the emergencyHeat command in My Ecobee DTH.
You can call this method within webcore (Rule Engine) according to your own requirements.
For no 2, I believe that you refer to the auxMaxOutdoorTemp attribute in the ecobee APIs which can also be set with webcore by calling the setAuxMaxOutdoorTemp command in the DTH according to your own custom rules (and also your own schedule).
Hi, I added some new settings in ecobeeSetZoneWithSchedule (v8.6) for your use case (and more).
The smartapp is based on the concepts of rooms/zones/schedules.
In ScheduleSetup>OutdoorThresholdsSetup, you can now set the auxMaxOutdoorTemp attribute which means that you can set up different values during the day depending on the time and outdoor temperature. You can set some different auxMaxOutdoorTemp values when the outdoorTemp is less than a minimum outdoor temp value or greater than a maximum outdoor temp value.
The ecobeeSetZoneWithSchedule smartapp is part of My Ecobee Bundle at my store.
Hi Yves, thanks for the great work on the ecobee smartthings integration. Is it possible to use physical thermostats with temperature display and controls instead of the passive ecobee thermostat in each room/zone? Having an “active” (i.e. able to manually set the temperature) physical device on the wall is preferable for my needs so that I don’t have to worry about setting up mobile apps for guests or old folks who can’t use one. If there are hardware thermostat models that can work with your software, ecobee, keen and smartthings, could you comment about those, please. If the thermostat also has occupancy sensor, that will be great, but that’s not a dealbreaker.
Sorry if this question has been answered already - if you can point me to those, that will be great. I searched but couldn’t find such info, perhaps I wasn’t using the correct keywords?!
Hi, I understand that you would like to use physical thermostats in your zones/rooms, yes, it can be done in my zoning smartapps. In ecobeeSetZoneWithSchedule, you can use any ST connected thermostats (zwave, zigbee, Nest, Honewell) in RoomSetup. For each room, you can associate the thermostat of your liking as long as it’s connected to SmartThings and follows the ST standard capabilities. However, the"slave thermostats" will be dependent on the main master thermostat in terms of setpoints & thermostat modes. You can use the virtual zone devices to adjust your “slave” thermostats’ setpoints based on some temp delta vs. the main thermostat’s setpoint (+/- 3F for example).
It’s really up to you to choose the best room/zone thermostat for your needs. I don’t know anything about your requirements (will it control some in-line baseboards, fireplaces, hot water valves, mini/window splits, portable heaters/coolers ??) and this is bit outside of the scope of my code.
For windows/mini splits, and portable heaters/coolers, I can refer you to the Flair puck and my thread below.
Please refer to the ST community wiki for more details about zone/room thermostats in ecobeeSetZoneWithSchedule.
If you have some specific questions, it’s easier for me to keep track of your communications via gmail conversations at email@example.com.
P.S. Of course, you can also use a ST connected thermostat for its temp or motion sensor capability in my smartapps as long as they support the corresponding ST standard capabilities in their DTHs. For example, My Nest implementation does it just like My ecobee device.
Just want to inform my contributors and all ecobee users that new versions of MyEcobeeDevice(v5.9.9x.8), and MyEcobeeSwitch(v1.0.4) can be downloaded at my e-commerce solution provider (sellfy) using the original download link or your sellfy account provided that you’ve followed the update procedure indicated at my store (under the terms of service).
**The new versions are even more resilient to the ST timeout/scheduling (due to rate limiting) or the ecobee server issues that affect the SmartThings integration.
Refer to the ecobee status page for the recent ecobee outages:
You basically just need to install the DTHs once, and forget about it. The code will recover and resend any failed thermostat or switch command in the next hour window after an ST or ecobee outage. No other ecobee implementation (and especially the ST stock device) can match this level of resilience and reliability.
If you’re are a contributor to one of my support packages (and I have access to your ST account), the upgrade has already been done for you. You don’t need to do anything, everything has been taken care of.
All the complimentary smartapps ( with My Ecobee device) are located at my github and are explained at the ST community wiki (all ecobee* smartapps):
I am running the latest version of your device and smart app. Been working great for a year, over the last day lots of problems. Smartthings now only gets set point updates and remote sensor updates not operating state changes such as heat on or idle. Are others experiencing this? Its also the same in the Ecobee app and Ecobee website so it looks like an Ecobee problem.
Now, when you say the latest version, do you mean My Ecobee device v5.9.9x.8e and MyEcobeeInit v4.1b? If not, I strongly recommend to you to update to those versions as I’ve made some refresh token logic enhancements in the last minor versions …
Otherwise, please refer to the ST community wiki for any issues, there are some explanations & recommendations (ex. watchdog).
To be clear, this is not a problem with authentication, I still receive thermostat set point updates, remote sensors temp updates, just state changes for heating, cooling, or idle are not updating for the last 24 hrs.
From my logs, ecobee has gone from a 1-3 min api update from temp or tstat change to a 15 min api update. This is an unacceptable lag for a modern day product to process single value data and spit out an api update.
Apart from the current situation where some ecobee API infos are missing due to the ecobee frequent outages (equipmentStatus/OperatingState, occupany from the ecobee’s remote sensors), My Ecobee device just works normally and can reissue your thermostat commands when the (ST/ecobee) temporary outage is over. The code has been refined over the years and proven to be reliable and resilient to most of the ST/ecobee outages in the past months.
You do not need to re-login in the middle of an ecobee outage as my code is able to re-issue the auth tokens during or after the ecobee/ST outage.
Please subscribe to the ecobee status page in order to get notifications about upcoling scheduled maintenance or current ecobee issues (if any).
Hi, I don’t use webcore, but I can tell you that the limitation is on the webcore side, not My Ecobee. Please contact webcore support for any webcore issues.
FYI, if you have multiple thermostats, you can also use the iterateXXXX methods in My ecobee device to set the same thermostat settings on multiple thermostats. You can then use only 1 thermostat to do so (and not load the others).
Refer to the ST community wiki for more details on the commands available: