[RELEASE] Lock User Management (LUM)

Hi, new to all of this but have 3 Schlage Zwave locks and cannot get them connected into SmartThings ! tried resetting, repairing, etc etc and nothing works.
maybe a stupid question, but does this lock device handler make it easier or make it defiantly connect ?

Device handlers come into effect after the pairing is complete. However if you have old unused device handlers installed it could cause issues due to a bug in the platform where it marks unused device handlers stale. See this topic for details. You should try to exclude your locks (resetting them is not the same as exclusion) before trying to pair them as explained on this post.

@RBoy / @maddie I’m seeing the same issue now as well. New Schlage Locks @ new location. Had these same locks at previous location, and never saw this.

Anyone find a solution here? I get a double notification for xxx door opened with yyy UserName, followed by opened with Master Code. Which it certainly wasn’t, as I have no clue what it even is.

I tried setting all locks to max users, and running clear codes, and then adding the set of users back. Same thing seems to occur.


Hi how do I access the above function in the LUM app, I cannot find this “setup arm stay button actions for keypad” page!

Thanks

I have idlock 150 and tried to write some codes to it. I first did the clear all codes thing. And that did even reset the mastercode to “123456”… But when trying with other codes it doesn’t work. They are green in LUM, but doesn’t work on the lock. I even tried factory reset the lock with no luck.

Any help?

With the IDLock you would want to start with using the Enhanced Z-Wave Lock device handler. Thanks stock device handler doesn’t always work with IDLock. If it’s showing up as green that means the lock has successfully programmed the code. If it still doesn’t work it’s a local lock issue. I just checked and it’s working here. This lock has a finicky keys and they don’t always register when you press them the first time so wait for the beep to ensure it registers when you press the key. The other thing to look for is to ensure that the privacy/vacation mode is disabled on the lock as those features block the user codes from operating the lock when enabled (even if successfully programmed).

1 Like

I can’t find options for privacy/vacation mode in the manual… The only thing is the away mode that we literally never uses. And that is automatically deactivated when unlocking the door.

So what should I do? Could it be the zwave module that’s too old?

Got this for a Yale Conexis L1… Love it, works well and to have the ability to set timers for auto lock or even switch off is a dream, tied up with Smartthings and Sharptools dashboard works so well, nicely done.

1 Like

Hi

Have we any info on an edge driver replacement for the RBoy lock DTH
Thanks

tagging @RBoy

Hi,

I’m wondering if the @RBoy apps will work when we switch to edge?

Not sure if that’s quite the same question.

Thanks

LUM and RBoys other lock projects work with any device that exposes the right capabilities so Edge itself should not be an issue (ok the device handlers RBoy supports will need to be rewritten as edge drivers, but thats a different problem.)

The plans for LUM itself though. When Groovy goes away, no more LUM. Unless RBoy and team create a new smartapp to replace it. (im pretty sure they’re already planning behind the scenes). I for one am very interested in what THAT looks like and if they’ve made a decision on future direction yet.

2 Likes

Thanks.

Hard to know what to go with at the moment and still no direction from ST as to when the change will be.

Most of us are assuming within 8-12 months. Id consider it imminent at this point.

I had to leave the platform due to the ridiculousness around the 200 devices ll limit but before i moved i was already dumping anything based on groovy as fast as i could find replacements. I had expected LUM to be my last holdout besides webcore.

But @RBoy - if i were still on the platform… Id DEFINITELY be beating the doors down for the plan at this point. It may not be done but it’s time to make plans.

2 Likes

@nathancu what platform are you on now?

I’ve been using the LUM since it come out and has been solid and very useful for me so I hope RBoy can produces something similar with an edge driver.

Hi there, got the LUM running very well, users in and all seems to work well, apart from the speak notifications just does nothing, the Google nest show like there is something about to be said then nothing? Any ideas… ? Cheers.

Scrap that I am an idiot, 6 is 6% not volume level 6 that’s 60… lol… Sorry

What is the difference with keyboard and manual

What do you do with locks with rfid and fingerprint reader, Can you get nothification on the iser there to

Keypad is punching in a code to lock/unlock.

Manual is throwing the bolt lever to lock/unlock.

As to the other, Ill leave that to someone who knows.

1 Like