[RELEASE] Lock User Management - Door lock code manager (create, delete and schedule codes) with automatic lock/unlock, custom user actions and SHM/ADT integration (LUM)

Thanks for responding.

Thanks for pointing me toward manual keypad programming to do this. However, although I was able to find the ability and the key presses needed to change the length of the user codes on other Schlage locks, the FE599 does not seem to have this ability. At least (and I’d be happy to be wrong), I was unable to find it anywhere. I even tried using what works on the other locks but it didn’t work on the FE599. None of the FE599-specific information I found showed that this was possible.

On this one, the DTH doesn’t seem to show me anything to turn auto-lock off on it’s main screen or under the ‘gear page’. The main screen only shows the following tiles:

  • Lock
  • Unlock
  • Code Entry On/Off (vacation mode)
  • Audio On/Off
  • Battery Strength
  • Refresh

I’m using:

And, just in case, here’s the IDE info from the lock:

Data * MSR: 003B-634B-504C

  • manufacturer: Schlage
  • networkSecurityLevel: ZWAVE_S0_LEGACY
    Raw Description zw:Fs type:4003 mfr:003B prod:634B model:504C ver:43.37 zwv:2.64 lib:06 cc:85,73,72,98 sec:62,63,80,71,70,86,20
1 Like

You’re right, I mixed up the FE599 with a different model.

  • The FE599 doesn’t have auto lock. It’s an electronic latch with a relock that’s triggered about 3 seconds after it’s unlocked using a code. This can’t be changed, it’s how the lock is designed. The only way to leave it unlocked is to press the unlock button on the inside or unlock it remotely. Keep in mind that even if it’s unlocked, once a valid code is entered on the keypad it’ll relock itself after about 3 seconds.
  • It also has a fixed code length of 4 digits unlike other Schlage locks

No worries. I understand.

I’d rather have 6-digit codes but I’ll live with the 4-digit codes. At least the lock has individual buttons for each digit as opposed to the doubled-up buttons on the Kwikset it’s replacing. This reduces the chance of getting lucky with keypresses.

As for the 3-second auto lock, I think that’s OK too (since I have no choice). In addition, I note that by manually pressing the unlock button on the inside of the door/lock, the lock will stay unlocked indefinitely. So, I’ve written two webCoRE pistons:

  • The first automatically relocks the door after 5 minutes of being unlocked. It then checks up to five times to ensure that the lock has actually been locked.
  • I then created an ‘override’ virtual switch that keeps the door unlocked for two hours - relocking it automatically after the two hours expires. It also includes the 5x confirmation to ensure it’s been locked

So, I have a full range of security/convenience solutions in spite of the auto-locking inflexibility within the lock. An automatic 3-second locking when entering a user code and then the 5-minute and two-hour automatic relocking based in webCoRE.

Thanks again for your time and great apps and DTH’s.

BTW, I installed this lock on Friday and it has performed perfectly in every instance since then and hasn’t fallen offline at all. It’s a big change from the increasingly flaky Kwikset 912 I’ve been fighting with for many months - even after replacing the Z-Wave module.

1 Like

There’s another issue with Kwikset locks. They won’t accept two codes that use the same key combination. For example if you try to program 1234 and 2134, even through they are different codes some of these locks like the Kwikset 888/910/912 will reject the second code because it can’t differentiate between them when the user enters the code because they are sharing the same key press order.

Also see this topic for another issue we discovered with the 910/912 locks regarding programming issues:

2 Likes

I agree about this issue. It’s another one of the reasons I went to 6-digit user codes on the Kwikset but am OK with 4-digit codes on the Schlage.

From another thread, it appears that Kwikset Support says that when the lock drops off the network and a yellow light shows next to the ‘A’ button in the 912 Lever Lock and 910 Deadbolt Lock (that we know of) , it indicates that it’s possibly a bad motherboard. Not good.

2 Likes

Ran into a problem. The door would unlock itsself after being locked. Every time you locked it it would unlock. Discovered the door switch was louse and the manager thought the door was open. Disabled the unlock option. And fixed the sensor.

But this is major security flaw if someone shakes or forces a door and the sensor opens the door would unlock for them. Basicaly all you have to do is force the door open so the sensor opens and wait for the door to unlock.
This option needs to be removed. And everyone needs to be warned to turn it off…

1 Like

I noticed yesterday my batteries were down to 1%. They seemed to have drain very fast all of the sudden. Today is was not locking and unlocking & it was unresponsive from the app. I did a zwave repair and i.noticed it said failed to repair lock, lights & mesh. Now it seems like its qo3king but slow? Has samsung doing updates that we are unaware of? It seems like my whole zwave network is buggy.

Hoping someone can help. My schlage lock is not responding to any commands & does not lock automatically anymore. Had an issue with batteries a few days ago & I replaced them. Am I correct that I need to exclude the lock from zwave & repaor?

@RBoy can you help me please?

. I have 4 of these locks. try removing it then send the zwave exclude command which should reset it. then reconnect. When reconnecting it has to be close to the hub. I remove mine from the door and bring it to the hub to include it or the key excange will fail.

1 Like

Looks like he figured it out, apparently his apps and DTH’s had disappeared after he re-paired the lock. Maybe he can clarify if was an IDE issue or something else:

For some strange reason the lock unpaired. I repaired it but it still didnt work. After trying a few times I googled searched because smartthings search is not as detailed. I had to reset it & repair it & everything came back. Reason why I posted help was because I have night nurses for my daughter & I was afraid of royally screwing things up.

1 Like

I installed the Device Handler, then I installed the LUM app. I must have done something wrong, because it did not erase any of my existing codes. When I add a new user with a new code, the code is not opening the lock.

I’m not sure how to get it to accept new codes.

I just noticed I received a text alert:
Retry programming exceeded. user 3 (Name) addition not confirmed by lock

What am I doing wrong How do I get the lock to confirm the programming?

You aren’t doing anything wrong, your lock is having trouble with the mesh. Assuming your battery is good, see this:
FAQ: why would I need another beaming repeater if my zwave lock is already close to my hub?

2 Likes

@RBoy This is a really great SmartApp. Thanks for putting all that effort in!

2 Likes

Are you going to make updates to support the new Schlage Connect Z-Wave Plus locks?

Has anyone ever had an issue with their Schlage Connect locks that won’t allow you to add custom user codes? These locks have always worked perfectly for me until recently. I tried a full factory reset on the locks and completely defaulting out the smartapp (removed all users etc). I re-added everything and it still doesn’t work. This is the error I’m seeing in the app. Any ideas? I have the latest device handler and smart app installed and i also renamed the device handler to “Z-Wave Lock” as suggested.

I went out and purchased 1 repeater and placed it within 10 feet of the door and was still having issues. Then I went out and purchased a second one and put it on the other side of the door, also within 10 feet.

The repeaters I purchased are: https://www.amazon.com/GE-Weather-Resistant-Required-Works-SmartThings-14284/dp/B06W9NWFM3

The issue is, after I program lock codes, I wait about 30 minutes and try and the codes all work. But then within 24 hours, the codes stop working. Then I add them back in, and they work again for some small period of time, but then stops working again.

Also, in the app, it appears that the users are sometimes green, sometimes yellow.

© 2019 SmartThings, Inc. All Rights Reserved. Terms of Use | Privacy Policy

SmartThings; SmartApps®; Physical Graph; Hello, Home; and Hello, Smart Home are all trademarks of the SmartThings, Inc.