SmartThings Community

[RELEASE] Lock Manager

smartapp_locks

(Erik Thayer) #1146

They’re fine in the unpublished state, they’re fine published too! In some cases, like sharing SmartThings accounts it might be a good idea to publish them anyways.

You should be able to see the app in your phone in the SmartThings app now under ‘Marketplace’

Is this not the case?


(Josh Gruberman) #1147

I do see Lock Manager under My Apps in the Marketplace, I was just trying to make sure I followed the directions in your Guide. I was a little lost following page 12 here: https://www.dropbox.com/s/pfi9ciqmxbjq9lo/guide.pdf?dl=0


(Erik Thayer) #1148

I can see how that is confusing. I’ll change this in the next guide.

If you followed the steps above page 12, you can ignore it and move on. I put that page in there to illustrate some details for people who may not want to use gitHub. Since gitHub connect is my preferred method of installing the app, I purposefully didn’t go into detail about doing it manually

TLDR;
Skip page 12.


(Josh Gruberman) #1149

Gotcha! that makes sense… and I had a feeling that’s what I needed to do but I didn’t want to skip the page and go ahead and something was wrong and I asked for help but didn’t follow instructions :slight_smile:


(Josh Gruberman) #1150

Is there a way to get the keypads to chime when a door is opened?


(Arn B) #1152

If you are using a keypad only device such as: Iris, Xfinity or Centralite; then yes my SHM Delay smartapp issues EntryDelay tones.


(Jarrell) #1153

Hi,

I followed all of the directions to installing your app and have the latest updates. I can add new locks fine. When I try add a new user and “tap to set” the name; I get a brief loading animation then nothing happens. It won’t allow me to enter a name. Also when I “tap to show” my locks I get “Error: Can’t find lock!”. I’m running this on a Lumia 950XL on Windows 10 Mobile build 10.0.15250.0. My version of the smartthings app is 1.7.28140.0. This is the latest version for windows mobile. Any help?


(Josh Gruberman) #1154

I have my door to disarm the system when I unlock it and I went to unlock and open the door and the alarm(siren module) went off. I tried to input my code and Off on the keypad but no help… It was still screaming.

How do I disable the alarm when it’s going off? And ideally… WHY was it going off? @ethayer?


(GP) #1155

I see everyone going thru alot of work for entry/exit delays and beep on entry/exit with a keypad/phone/ect. I have:

iris keypad (centralite)
lock manager (e thayer Thanks!)
zipato siren (any smart siren will work)
webcore
(and of course sensors, 2 contact and 1 motion for now)

With these four things I am able to have entry/exit delays, keypad beep on arming/disarming, siren beep on arming disarming, siren and keypad warning beep on entry/exit when alarm is armed and push/text notifications for it all. I have done this WITHOUT using:

SHM (smart home monitor)
smartalarm (smartapp)
smarthome (smartapp)
SHM Delay (smartapp)
Virtual Delay Contacts (made in IDE)

I simply have used webcore (or core would work I believe) to make rules for entry delays and beep/siren/push/sms actions. I then used lock manager to program the codes (4 digit for the keypad) and set the exit delay ONLY in this smartapp. I can arm/disarm the alarm from my mobile or keypad or vice versa and it syncs correctly, beeps and delays. All this without using SHM too. The trick is to setup SHM but do not fill any fields for sensors, motions or sirens…leave them blank and then set your rules with webcore or core. If you want more info let me know and I can try to help. Here are some screenshots of my webcore:


(Erik Thayer) #1156

Messages to the controller are not processed “in order.” They are processed when they arrive. Often, the message for the door sensor is much faster than the message for the unlock, plus additional processing is required for the app to trigger the disarm routine.

Here’s how I do it personally…

I have the same routine as the disarmed also trigger a light to turn on. You could also ‘toggle’ the light if you think that the light might be on to begin with. I know that when the light is ON, that the alarm state is also set to disabled. It usually takes 3 - 5 seconds.


(Josh Gruberman) #1157

Got it - and how do I turn th alarm off? I couldn’t get it to stop so I had to unplug the siren lol


(GP) #1158

in smartthings you can always turn the alarm off in the device details page…it should have an off button kind of like a light switch would have in smartthings


(Erik Thayer) #1159

The way I do it is to also have the routine turn off the alarm. I run it through CoRE so that might be a feature the regular routines don’t support… so a successful code unlock will also turn off the alarm and set SHM to disabled.

So, if I make an error and the alarm is going off, I’ll lock the door and then enter my code again… the trigger happens and turns off the alarm for me.


(Dylan Corbett) #1160

Any idea what the cause would be for it to keep saying lock set failed while trying to set up? Do I need to add the lock from scratch? I’ve had it running using the Schlage DH for quite some time now but am interested in trying these additional features. My lock is a 469.


(Arn B) #1161

Many wall powered sirens have an undocumented internal jumper switch that activates battery backup, preventing an intruder from killing it by pulling the plug. Information in this link worked for my GoControl siren.


(jkp) #1162

Make sure you have the updated DTH for the schlage lock. It can be found here:


(Dylan Corbett) #1163

Thanks for that. I have verified I do have the correct DTH installed.


(matthew@mcinteer.net) #1164

Yale YRD256 Burn code and scheduling not working. You probably know this already, presumably because Yale locks not reporting codes other than 99 as noted previously. Just thought I should report for this model as well. Hopefully Yale will get back to you on this.

Thanks


#1165

Hi all-
I just started with ST, Lock Manager, and some schlage century and keypad locks. I installed everything pretty well, but on the Lock Manager app, it’s only showing “Installed” in gray without showing anything as being added (i.e., the installed locks), but shows “Create” in gray followed by “New Lock” “New User” etc. Same thing with “Locks” in gray: no options below it in white, but then it shows “Global Settings” with options such as “Notification Settings”. Any ideas why I’m not seeing all the locks and users I’ve already added to the smartapp? Thanks!


#1166

Erik (@ethayer) and Other Peoples

Does the app currently report on INCORRECT codes entered?
If so, how does it handle it? How can I react to it.
If not, can it be added?

[My lock did report the incorrect entry attempt; wording as found in the recommended lock DTH]

I have been using Lock Manager & its predecessor since inception, but just today had the strangest thing happen, as witnessed by the cameras: Woman walks up to the door & starts entering codes!!!

So necessity demands a solutions (well, a warped version of the expressions :slight_smile: )

Thanks in advance
J