Post Requests for Edge Drivers Here (community-created)

[Mariano_Colmenarejo]

@RobinScavok

Would it be possible to have a custom driver with this capability?

Hi @RobinScavok

I had forgotten that I was going to try to make a driver to configure the parameters of zwave devices.
Let’s see if tomorrow I get on today I have other things to do

UPDATE:
Driver published

(New Release) New Edge Driver Z-Wave Device Config Mc

(New Release) New Edge Driver Z-Wave Device Config Mc This is the initial version of the driver that allows reading and writing configuration parameters in Z-Wave devices. It also shows at the end of the details view the Manufacturer, productType and productId How does it work? Make a driver change to Z-Wave Device Config Mc on the device you want to configure. All values ​​displayed will be 0. Note: If you have automations that affect this device, they may be missing or disabled. Add a virtual device on them so they don’t get lost. Before the update of the android app they remained as an unknown action. Now the device will disappear from the automation and if in actions or conditions there is only this device, the automation is deleted. If there are more devices it will only be …

[NickA]

Has anyone created an Edge driver for the Monoprice HKZW-DWS01 Door/Window Sensor?

Raw Description zw:S type:0701 mfr:0208 prod:0201 model:0008 ver:1.05 zwv:4.34 lib:03 cc:5E,86,72,71,59,85,80,84,73,70,7A,5A

[Terri_Baker (TeBa)]

@Jason_Meudt

The fIrst, and foremost, is a Fully-Kiosk Browser edge driver. Here is the DTH that I am currently using:

I know this has been requested before but just wondering if any one would consider converting the Fully Kiosk Browser DTH in the linked post to Edge (if it’s even possible)?

[mooch91]

I use an older Monoprice Z-wave contact sensor (#10795) tied in to my smoke detectors via a relay (via external contacts). I’d like this sensor to be reflected in Smartthings as a smoke detector.

I also use the same sensor as a water sensor to identify leaks. I’d like this sensor to be reflected in Smartthings as a leak detector.

Are either of these configured as of yet?

Thanks!

[mooch91]

@damohabir

Back in the good old days, many of use were using Monoprice open/close sensors as smoke detectors, moisture, sensors, security system, etc. These open/close sensors had a pair of contacts internally that wires can be attached to, and then used, along with the modified DTH, for other purposes. I use them as moisture sensors, smoke detectors, and security system arm/disarm detection. This is the DTH that was used.

Monoprice-Connected-Smoke-Alarm/monoprice-connected-smoke-alarm.groovy at master · dan06/Monoprice-Connected-Smoke-Alarm · GitHub

Would appreciate Edge drivers for them.

Here is a thread on the discussion:

Monoprice door/window sensor and Smoke Alarm Device Type

@damohabir

Just requested the same. Have you come up with anything yet? Thanks.

[JDRoberts]

I know it’s a long way around the barn, exactly what you don’t want for emergency alerts, but @taustin does have a virtual smoke alarm and a virtual water sensor which can both be actuated (turned on or off) from a regular routine.

So you could have a regular routine where the trigger was your contact sensor and the action was “turning on“ the virtual device which serves as the alert trigger in smartthings home monitor or another automation.

The good news is all of this does run locally, unlike the old groovy custom versions.

So I don’t know if it’s of any interest or not, but it might be a workaround for the time being.

(The topic title is a clickable link)

[ST Edge] vEdge Creator: a virtual device generator for end users

Here is an Edge driver that will enable end-users to create virtual devices that run locally on-hub. UPDATED JULY 2022… Features: Supports the following virtual device types: A/C, air quality, alarm, battery, contact, door, fan, garage door, light, lock, momentary button, motion, panic, presence, refrigerator, shade, smoke, switch, temp/humidity, TV, switchlevel/dimmer, thermostat, video camera, water Create any number of virtual devices Easy and fast to use: No coding or CLI required Enables you to create 100% local automations with virtual devices See how many devices you’ve created of a given type (inventory) Devices include additional controls and features beyond what is available through CLI-created virtual devices Several virtual device types include a switch that mirrors cont…

@damohabir

[montyfert (martin)]

an edge driver for tuya local would be nice

[JDRoberts]

@montyfert

an edge driver for tuya local would be nice

The problem is that Tuya uses a lot of proprietary code, and they use different proprietary clusters for different models. So it all comes back to the model number. There are several edge drivers already for different tuya models. Which devices specifically were you looking for?

And have you tried checking the quick browse lists in the community-created wiki? That’s where you can find the existing edge Drivers for Tuya devices.

https://thingsthataresmart.wiki/index.php?title=How_to_Quick_Browse_the_Community-Created_SmartApps_Forum_Section#Quick_Browse_Links_for_Edge_Drivers

[montyfert (martin)]

the devices im trying to add are wifi devices some wifi gu10 bulbs , a Inkbird Digital Wireless Thermostat, ITC-308-WiFi Temperature Controller and a wifi led controller.

[JDRoberts]

@montyfert

the devices im trying to add are wifi devices some wifi gu10 bulbs , a Inkbird Digital Wireless Thermostat, ITC-308-WiFi Temperature Controller and a wifi led controller.

Ah, ok. I don’t think anyone’s looked at local control for those yet. I’m assuming you haven’t flashed them to Tasmota, this is the original firmware?

[montyfert (martin)]

i have a couple of things (sonoff things i flashed to tasmota ) but flashed them back to sonoff as they were so slow operating with the tasmota edge driver compared to ewelink to smartthings cloud

[montyfert (martin)]

there is a custom Integration for local handling of Tuya-based devices for (home assistant ) but i find home assistant too much hassle .

[hongtat (HONGTAT TAN)]

@montyfert

i have a couple of things (sonoff things i flashed to tasmota ) but flashed them back to sonoff as they were so slow operating with the tasmota edge driver compared to ewelink to smartthings cloud

The Tasmota Edge driver is 100% local vs eWeLink cloud. Could you let me know where is slow for you?

If this is slow, I think even if there is a Tuya local driver, it would still be slow for you.

[David_Kneebush]

How about a Edge Driver for Ring Contact and Motion Sensors.

[RobinScavok (Robin)]

Hi @Mariano_Colmenarejo

Thank you very much for de device config driver. It works perfectly! Now I can finish my migration to Smartthings. Hero!

[mooch91]

Is anyone working on drivers for the alarm keypads? Specifically, I have the old school Iris/Centralite keypad that I use to arm/disarm STHM, using the Rboy device handler and lock user manager code. Interested to see if anyone is getting these to work with Edge. Thanks!

[Chryth.jin (jin junhyuk)]

Hi
I need your help
please look at this post and reply me

[Beta] Zigbee Edge Driver compatible with Lidl, Ecosmart, Osram, SmartThings & Others

This device uses Tuya’s specific EF00 cluster and doesn’t work with my drivers. @ygerlovin or @veonua may have some driver for it

[DOWNSOUTH407 (DC)]

Does anyone know of a Edge Driver for the Hampton Bay Zigbee fan controller? When I checked the official list of Edge Drivers there is not even a category for Zigbee fans, only Z-Wave. I am willing to kick in some money toward the development of an Edge Driver.

[montyfert (martin)]

please can we have an edge driver for the cast web api as there will be nothing like it after the groovy goes
thanks

[Helder_Rodrigues]

Good night @Mariano_Colmenarejo
Can you create driver for this device?
I deleted it from Smartthings and when I add it it shows up as Thing.

I have your Zigbee Switch MC driver, but it won’t let you select

Data * application: 43

• endpointId: 01
• manufacturer: _TZ3000_tqlv4ug4
• model: TS0001
• zigbeeNodeType: ROUTER
  Raw Description 01 0104 0100 01 07 0003 0004 0005 0006 E000 E001 0000 02 0019 000A

if I go to groovy and change it to zigbee switch it goes to local and it works…

But when groovy goes down I can’t add it anymore…

Sorry for the ignorance…
When you add a new device what are we supposed to do?

Thanks