Hi I have those drivers yeah and my hub is registered to Marino Chanel 
I will get them shoots for you one sec…
The IDE I have now…
I will double check tomorrow as have to do this via computer.
Right I will check and install this driver in the morning.
Is it working fine with this driver?
I reset this button paired and reset it again few times and I’m running into the same issue.
Also each time I install the button it shows me a different battery level.
To get the Ikea button to install I had to put a new battery in, set it right next to the hub, reset it, and then add the button. If I remember correctly I had to reset and add it several times before it paired correctly and worked. Also, let it sit (app and device) untouched once added for 1-2 mins just to be sure you don’t interrupt the pairing process. The Ikea devices were the most difficult to add so far.
1 Like
When I added these buttons months ago all went smooth and well. I’ve seen few of these posts about having problems now. I think this could be a new issue.
1 Like
Yes
I have used zigbee button driver from January 2022
I didn’t get IKEA button to work using Zigbee Switch Mc driver
I paired new IKEA button ( on / off switch )
Then I changed driver to
IKEA button’s cluster etc
Then I changed button to use Zigbee Button driver
1 Like
OMG all of that seems to complicate for me. I have no idea how to install new drivers. It happened that some of them came with new hub update but non of them seem to work or it takes to much hassle from what I read to make it work.
How do I switch back to device handlerer and IDE ?
I have no idea how to install those drivers :(((
Is this driver in your channel/? smartthings zigbee switch stock beta driver.
See instruction here
Preview | SmartThings-managed Edge Device Drivers - Devices & Integrations - SmartThings Community
1 Like
Thanks a lot. I am glad you understand that I’m only new to this and just slowly getting on with things how to find install and set up 
Thanks
Hi. Found 3 phase variant.
According to: [Device Support Request] 3Phase Hiking Tomzn Power Meter DTS238-7 Zigbee (analog of Single Phase DDS238-2 Zigbee) · Issue #1298 · zigpy/zha-device-handlers · GitHub
It uses Ef00 cluster. So no luck with your drivers…
Correct, it does not work with my driver
@N_Mendes, @Udah1, @dotan_shai, @flotueur
Added these devices to this driver version
┌─────────────┬──────────────────────────────────────┐
│ Name │ Zigbee Multi Switch Mc │
│ Version │ 2022-08-05T12:00:18.149650245 │
└─────────────┴──────────────────────────────────────┘
- id: "Zemismart/_TZ3000_zmbedyhc"
deviceLabel: Zemismart three Switch
manufacturer: _TZ3000_zmbedyhc
model: TS0003
deviceProfileName: three-switch
- id: "Zemismart/_TZ3000_sieosxue"
deviceLabel: Three Switch
manufacturer: _TZ3000_sieosxue
model: TS0003
deviceProfileName: three-switch
- id: "Zemismart/_TZ3000_pc0qmva4"
deviceLabel: Two Switch
manufacturer: _TZ3000_pc0qmva4
model: TS0002
deviceProfileName: two-switch
- id: "Lonsonho/_TZ3000_fisb3ajo"
deviceLabel: Two Switch
manufacturer: _TZ3000_fisb3ajo
model: TS0002
deviceProfileName: two-switch
- id: "LIDL/_TZ3000_vzopcetz"
deviceLabel: Lidl MultiPlug
manufacturer: _TZ3000_vzopcetz
model: TS011F
deviceProfileName: three-outlet
1 Like
Any chance of adding this?
Smartenit ZBMLC30
Data * zigbeeNodeType: ROUTER
- firmwareManufacturerCode: 4213
- firmwareFullVersion: 44050000
- application: 44
- endpointId: 01
- firmwareImageType: 25
- manufacturer: Compacta International, Ltd
- model: ZBMLC30
Raw Description 01 0104 0002 02 06 0000 0003 0006 0004 0005 0008 01 0019
Would be great if so, otherwise thanks again for all your work.
Could you tell me what device it is?
The clusters you send me and those of the DTH you use do not match.
According to the DTH it is a Metering Dual Load Controller:
fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0702", outClusters: "0019", model: "ZBMLC30", deviceJoinName: "Smartenit Metering Dual Load Controller"
and according to the clusters sent, it does not have clusters.simple_metering (0702) and if it has level (0008)
It’s a 110v/220v dual load multi-switch/relay
It may be too much of an ask to recreate the original function I don’t recall exactly when, but there was some change with Smartthings that broke the official DTH, But works with official Zigbee switch DTH, with Main controlling both relays, which was fine as far as controlling both loads simultaneously i.e. 220v.
What I can do is add it as a double switch to the zigbee multi switch Mc driver.
This controller allows you to turn on and off the 2 switches individually or simultaneously.
Does will not measure power.
1 Like
Good enough for me. Thanks so much Mariano!
Added to this driver version.
Try it and if not work fine tell me
┌─────────────┬──────────────────────────────────────┐
│ Name │ Zigbee Multi Switch Mc │
│ Version │ 2022-08-05T15:48:32.391308013 │
└─────────────┴──────────────────────────────────────┘
Remember that this driver has the possibility in preferences settings to choose a single or multiple mosaic to show all the switches in the mosaic
- id: "Smartenit/ZBMLC30"
deviceLabel: Smartenit Two Switch
manufacturer: Compacta International, Ltd
model: ZBMLC30
deviceProfileName: two-switch
1 Like