(EDGE Driver-Mc): Zigbee Drivers for Motion, Open/Close, Moisture, Smoke-Co Sensors and others Devices

I need the fingerprints, could be is added yet.
Try zigbee switch Mc

1 Like

And another one that looks the same, but with Manufacturer : _TZ3000_vd43bbfq


Hello @dotan_shai

I have no idea how to do what you want.
I do not known the commands used by tuya to start the calibration.

I don’t have any zigbee windows driver either

If you can , please have a look in Zigbee Herdman converter. This module is completely supported.
look in this file lines 47 to 59

Hi Mariano,

Is it way to separate the switches?
It means that they will appear each separately and not one inside the other


Yes, you can do it with Virtual Switch and simple automation
In order to create a virtual Switch please use Vdevice Creator by @ygerlovin

Hi @111167

Switches cannot be separated.
As they told you, You can create a virtual device and synchronize it with automations. There are several posts about this on the forum.

You can also select a multiple mass in settings and control all the switches from the mosaic

Hi @dotan_shai

I looked at it, but I don’t see how to do it.
Sorry, maybe others can help you with this


Does this driver support 4 gang switch? I tested this driver with 3A Smart Home switches, The1 gang , 2 gang, 3 gang switches work fine with this driver, but the 4 gang switch seems does not work. Can you tell me if the issue is just that this 4 gang switch is not added in the fingerprint file or not support 4 gang switch at the moment?

  • ZigBee 4 Gang Switch
  • manufacturer: 3A Smart Home DE
  • model: LXN-4S27LX1.0

Hi @3asmarthome

Yes, need add the fingerprints to assign the profile

When i have acces to CLI, i Will add it

Hi @Mariano_Colmenarejo,

Somehow if i do automation to synchronize the secondary switches with virtual switch, it doesn’t work.
Do enlighten.

Using _TZ3000_fvh3pjaz.

Hi @Hwa_Hwa_Ong

How did you do the automations?

Hi @Mariano_Colmenarejo

It is done through custom routine and mirroring virtual device with switch 2.
However, when the virtual device is turned on/off, main switch turns on along with switch 2. I’m not able to exclude main switch from the logic.

I have also tried to use smart lighting to mirror only for switch 2, but nothing happens.


I think is a issue with IOs App. In then part not show all switch actions options

This is the Android app then part:

These are the automations I use:

Luz Entrada, switch1 is the second component of a double switch
Lampara Salon-2 is the virtual mirror device

@Mariano_Colmenarejo ,

You are right. iOS app bug. Thanks.

Working perfectly now. Got to create the custom routine using Android.

1 Like

I am likely stupid, but where the heck are the drivers. I am in literally 10 clicks deep and no driver. I have installed other edge drivers, but the one I need for Sylvania Smart+ zigbee bulbs, seems to be buried behind endless links.
Can anyone help?

Hi @Rxich

All my drivers are in this link posted in the first post of the thread

Awesome, Thank you for all of your work developing these drivers and for sharing the link, so clear even an idIOT like me could find them.

Is there any harm in loading many drivers, unsure what devices I might buy later? and does the hub select the best match if I have >3 zigbee socket drivers?

Thank you again

There is a limit of 50 drivers allowed to be installed so just be aware of that, otherwise no harm.

1 Like

There is a limit of 50 drivers (not devices). I would not load up on drivers because if it’s not there when adding a device, ST will add the driver unless the device isnt known to ST via its fingerprint.

1 Like