Hi,
I have a problem with Fibaro Switch Single module.
The status updated OK when using Smartthings App, BUT , does not chaged when toggling from the mechanical switch. I can see messages in CLI when logging this driver. The following is turn on and turn off log via mechanical switch.
Please advise… @dotan_shai helped me
I replied this via PM to @dotan_shai
I need you to confirm that the switch cable is connected to the S1 input of the physical switch.
The stock driver and mine expect a source endpoint of 0 or nil and the device is sending source endpoint=1
local function switch_binary_report_handler(self, device, cmd)
if cmd.src_channel == nil or cmd.src_channel == 0 then
SwitchDefaults.zwave_handlers[cc.SWITCH_BINARY][SwitchBinary.REPORT](self, device, cmd)
end
end
The S2 input is used to send scenes and therefore is not allowed by code to emit a switch state change.
If you confirm it, I will modify the code of my driver since these changes would affect more users.
On the other hand, if it is well connected, you should also report it to smsrtthings so that they can fix the stock driver.
@Mariano_Colmenarejo @omergranot88
I’ve got the same behaviour w this device and driver. As it sits in a remote location I’m not able to use the CLI to make a log at the moment. It works well using the app and routines, but not using the physical switch. (The S1 is connected)
I am going to correct the code and if it works well you should notify smartthing so they can fix the stock driver
@S.F.B @omergranot88 update
Modified in this driver version:
In preferences you can configure S1 and S2 send scenes but it not will works until button1 and button2 added to profile.
I can’t debug this profile change and therefore I leave it without fixing
Need this profile modification
You can install immediately this driver version with CLI with command:
smartthings edge:drivers:install
───────────────────────────────────────────────────
Name Z-Wave Switch and Child Mc
Version 2023-04-03T19:58:02.016897363
───────────────────────────────────────────────────
2 posts were split to a new topic: [Edge drivers] Issue with stock Z-Wave Switch driver (Fibaro single switch)
Hi @Mariano_Colmenarejo
Sorry for the delay but i had no time before.
For me i need an edge driver button because is more like the keyfob but with only 2 buttons.
however when I look at the devices compatible with the button edge drivers I see the fibaro button and the keyfob but not the fibaro walli controler.
can you add it in your edge drivers or i have not yet understood how smartthings works
Thank you
Just wanted to say thank you for the Smart Implant driver, Mariano. My gate is now working again!
New version of Z-Wave Switch and Child Mc:
───────────────────────────────────────────────────
Name Z-Wave Switch and Child Mc
Version 2023-04-06T11:23:43.217297079
───────────────────────────────────────────────────
First of all, thank you Mariano for the Fibaro Smart Implant (FSI) driver. I can finally see the value of the onboard temperature sensor.
I still have one issue. I have two DS18B20 temperature sensors connected to the FSI but I can only get a temperature reading from one of them. When I connect each one individually they each work correctly so I believe the sensors and wiring are correct. When I connect them at the same time to the FSI the driver reports “- ‘C” for the second one.
I’ve also tried to get it to work with and without the 4.7K ohm pull-up resistor on the serial line. There is no change in the behavior.
In order to try and get the driver to recalculate what temperature sensors were attached I went into Settings and checked “6 External Temp Probe”. The log file output at this point is here.
Has anyone been able to get more than DS18B20 temperature sensor to work? If so, could you please give me any ideas on what else I can try. Thanks.
I have two sensors working for several weeks using Smart Implant Beta-4 driver. Try remove Smart Implant and then rejoin Smart Implant when both sensors are connected.
@TapioX, thank you for the suggestion. I removed and reinstalled the device again this morning and, unfortunately, only one external temperature probe is providing a reading.
Do you use a pull-up resistor in your configuration?
I’m not using pull-up resistor.
Both sensors are connected using 1 meter cable.
@Mariano_Colmenarejo
Can you please add the following parameters to
Fibaro Roller Shutter 3
This parameter allows reversing the operation of switches connected to S1 and S2 without changing the wiring.
Available settings:
0 – default (S1 – 1st channel, S2 – 2nd channel)
1 – reversed (S1 – 2nd channel, S2 – 1st channel)
Default setting: 0
Parameter size: 1 [byte]
And also
This parameter allows reversing the operation of Q1 and Q2 without changing the wiring (in case of invalid motor connection) to ensure proper operation.
Available settings:
0 – default (Q1 – 1st channel, Q2 – 2nd channel)
1 – reversed (Q1 – 2nd channel, Q2 – 1st channel)
Default setting: 0
Parameter size: 1 [byte]
Thanks
Hi Mariano
Would it be possible to use this to make the child device(Edge_child) display the power and energy?
Is it possible to make the child device display the energy and power?
I integrate Smartthings with Home Assistant and use the energy and power there.
Thanks
HI @Ped
Sorry, this requires modifying and adding quite a few things to the driver.
I don’t know if in the future I will have time to do it, right now I don’t have it.
The stock Zwave Switch driver has it done
Thanks, appreciate the reply.
Can’t seem to get my Fibaro devices to work properly with the stock drivers.
Your drivers have been a life saver.
Thanks again
@Mariano_Colmenarejo
This pictures sent from a friend of mine:
Looks like the reverse polarity is missing… Can you please check
This profile in your screenshot is for a qubino-flush-shutter, is not for fibaro roller shutter 3
- id: QubinoFlushShutter/AC
deviceLabel: Qubino Window Treatment
manufacturerId: 0x0159
productType: 0x0003
productId: 0x0052
deviceProfileName: qubino-flush-shutter
- id: QubinoFlushShutter/DC
deviceLabel: Qubino Window Treatment
manufacturerId: 0x0159
productType: 0x0003
productId: 0x0053
deviceProfileName: qubino-flush-shutter
name: qubino-flush-shutter
components:
- id: main
capabilities:
- id: windowShade
version: 1
- id: windowShadeLevel
version: 1
- id: windowShadePreset
version: 1
- id: powerMeter
version: 1
- id: energyMeter
version: 1
categories:
- name: Blind
preferences:
- name: "operatingModes"
title: "Operating Modes"
description: "Set the device's operating mode."
preferenceType: enumeration
required: true
definition:
options:
0: "Shutter mode"
1: "Venetian mode"
default: 0
- name: "slatsTurnTime"
title: "Slats turn time"
description: "Specify the time required to rotate the slats 180 degrees. (100 = 1 second)"
required: true
preferenceType: integer
definition:
minimum: 0
maximum: 32767
default: 150
- name: "slatsPosition"
title: "Slats position"
description: "Configuration defines slats return to previously set position after up/down
movement through Z-wave or push-buttons."
preferenceType: enumeration
required: true
definition:
options:
0: "In case of Z-wave control"
1: "Manual operation or limit is reached"
default: 0
- name: "motorUpDownTime"
title: "Motor up down time"
description: "Set the amount of time it takes to completely open or close shutter.
Check manual for more detailed guidance."
required: true
preferenceType: integer
definition:
minimum: 0
maximum: 32767
default: 0
- name: "motorOperationDetection"
title: "Motor operation detection"
description: "Power usage threshold which will be interpreted as motor reaching the limit switch."
required: true
preferenceType: integer
definition:
minimum: 0
maximum: 127
default: 30
- name: "forcedCalibration"
title: "Forced calibration"
description: "After selection '1' option, shutter enters the calibration mode.
When it is finished, completing full cycle - up, down and up, set this parameter value back to first option."
preferenceType: enumeration
required: true
definition:
options:
0: "Calibration finished or not started"
1: "Start calibration process"
default: 0