Hi, Please could you add the devices below:
Yagusmart Zigbee Smart Wall Light Switch (2 gang) Found here
Data * application: 50
endpointId: 01
firmwareFullVersion: 00000050
firmwareImageType: 54179
firmwareManufacturerCode: 4417
manufacturer: _TZ3000_atp7xmd9
model: TS0002
onOff: catchall
zigbeeNodeType: ROUTER
Yagusmart Zigbee Smart Wall Light Switch (3 gang) Found here
Data * application: 41
endpointId: 01
manufacturer: _TZ3000_wyhuocal
model: TS0013
onOff: catchall
zigbeeNodeType: SLEEPY_END_DEVICE
smedberg:
cl mfg-code 0x0000, delay 200, zcl global write 0x0000 0x0099 0x20 {01}, delay 200, send 0x0F70 0x01 0x01, delay 2000, st rattr 0x0F70 0xFF 0x0006 0x0000, delay 2000
This is sent in the device configuration write 1 in attribute 0x0099 of cluster 0x0000 and reads the state of the switch, attribute 0x0000 of 0x0006 cluster.
The write response should be seen a few seconds after the attribute write is sent.
With the edge driver, I already sent the value 1 to the attribute 0x0099 of the cluster 0x0000 and the device responded Attribute not supported.
Here we have an answer, this device does not support attribute 0x0099 of cluster 0x0000.
I’m going to change to what I did yesterday, write 0xFFFF in the 0x4001 attribute, onTime so that it never turns off the switch with timer
make a change to this driver, you do not need to uninstall it.
Install this driver on your hub
prepare the logcat to capture the pairing log to the new driver
let’s see what we see
┌─────────────┬──────────────────────────────────────┐
│ Name │ Zigbee Multi Switch Zemismart test │
│ Version │ 2022-01-25T17:51:16.900579 │
└─────────────┴──────────────────────────────────────┘
The exact model and manufacturer of the device, which appear in the IDE page, are necessary to add them to the driver
v.porsio
February 6, 2022, 5:24pm
#1556
@Mariano_Colmenarejo please add this motion sensor, Thanks !
01 0104 0402 01 04 0001 0500 0003 0000 04 1000 0006 0019 000A
HiSmartThings multiportuse sensor Mc:
endpointId: 01
Thanks in advance
psix.anp
February 6, 2022, 5:54pm
#1558
Next HopUnknown Device
And this
Data * zigbeeNodeType: ROUTER
application: 41
endpointId: 01
manufacturer: _TZ3000_pmz6mjyu
model: TS011F
uncledaveghr:
Can you add this device in for me onSmartThings multiportuse sensor Mc:
endpointId: 01
Was adde two days after with this driver version
┌─────────────┬──────────────────────────────────────┐
│ Name │ SmartThings Multipurpose Sensor Mc │
│ Version │ 2022-02-04T18:24:38.471734 │
└─────────────┴──────────────────────────────────────┘
1 Like
Added to this driver version
┌─────────────┬──────────────────────────────────────┐
│ Name │ Zigbee Switch Mc │
│ Version │ 2022-02-06T18:10:26.237378 │
└─────────────┴──────────────────────────────────────┘
- id: "_TYZB01_xfpdrwvc/Switch"
deviceLabel: TZ3000 Switch
manufacturer: _TYZB01_xfpdrwvc
model: TS0011
deviceProfileName: single-switch
Added to this driver version
┌─────────────┬──────────────────────────────────────┐
│ Name │ Zigbee Multi Switch Mc │
│ Version │ 2022-02-06T18:23:01.146605 │
└─────────────┴──────────────────────────────────────┘
- id: "TS0013/_TZ3000_wyhuocal"
deviceLabel: TS0013 Switch
manufacturer: _TZ3000_wyhuocal
model: TS0013
deviceProfileName: three-switch
- id: "TS0002/_TZ3000_atp7xmd9"
deviceLabel: TS0002 Switch
manufacturer: _TZ3000_atp7xmd9
model: TS0002
deviceProfileName: two-switch
syho
February 6, 2022, 6:24pm
#1562
Has it been been published? I couldn’t get my driver to install either.
Added to this driver version
┌─────────────┬──────────────────────────────────────┐
│ Name │ Zigbee Motion Sensor Mc │
│ Version │ 2022-02-06T18:27:27.648589 │
└─────────────┴──────────────────────────────────────┘
- id: "_TZ3000_msl6wxk9/Motion"
deviceLabel: TS0202 Motion Sensor
manufacturer: _TZ3000_msl6wxk9
model: TS0202
deviceProfileName: motion-battery
psix.anp
February 6, 2022, 6:32pm
#1564
Pls, add this too… Big thnx
Data * zigbeeNodeType: ROUTER
application: 41
endpointId: 01
manufacturer: _TZ3000_pmz6mjyu
model: TS011F
This afternoon, 1/2 hour ago or so I republished it in case I did it wrong the other day
syho
February 6, 2022, 6:35pm
#1566
Got it finally working. Thanks. I was going crazy wondering what I was doing wrong.
1 Like
I may not have published it correctly the other day, sorry
1 Like
syho
February 6, 2022, 6:38pm
#1568
No need to apologize. You’re very kind for all you do. Thanks again.
1 Like
Do you want us to try again and do you see in the CLI what happens?
What command do you use to get that list?, I get it without the names of the drivers
syho
February 6, 2022, 6:59pm
#1571
smarthings.exe edge:channels:drivers
Just went and checked, i had older ones, tried to delete them twice on smartthings app, each time the date moved forward, it now working ok thanks for the update
1 Like
