(EDGE Driver-Mc): Zigbee Drivers for Motion, Open/Close, Moisture, Smoke-Co Sensors and others Devices

HI @Mariano_Colmenarejo

Thank for your work , i used it with my sengled bulb ,ikea plug , but my ikea bulb is not working , not the same as listed .

Also can you add a third reality motion sensor and a neo cool cam motion sensor

Thanks

So my Smartthings successfully found the device as “Water Valve”.
I followed your earlier inx to reboot hub in IDE, clear cache (Android), but it’s not working properly.
The tile is showing the “Checking…” , and in the device shows no connection (cloud with line).

Something I’ve done wrong?

Thanks

@Mariano_Colmenarejo

Hi Mario. Thank you for your hard work here can you add this one? They are outdoor landscape lights. Please let me know if you need any more info. Thanks.



I have a little doubt, these lights are already added, but as RGB and tested by @milandjurovic71.
I see that you have them working with a DTH RGBW.

Does it work well for you as RGBW?

  - id: "OSRAM/Gardenspot RGB"
    deviceLabel: OSRAM Gardenspot RGB
    manufacturer: OSRAM
    model: LIGHTIFY Gardenspot RGB
    deviceProfileName: level-rgb

They are only RGB, but they create W by using all RGB at the same time.

1 Like

They work pretty well. Does your existing edge driver have the ability to make the color change slowly? Will it work with these lights?

Can not do that

@Mariano_Colmenarejo is the following device supported by your ZigBee switch driver. When I pair it, it gets added as a DTH device.

@Mariano_Colmenarejo is the following ZigBee switch supported by you ZigBee switch driver.

The TS0001 didn’t pair
The ST didn’t pair
The ST smart plug didn’t pair
The other 2 paired but without custom capabilities or battery

Troy Owens

added to zigbee switch Mc.

  - id: "Valve/TS0601"
    deviceLabel: Water Valve
    manufacturer: _TZE200_akjefhj5
    model: TS0601
    deviceProfileName: single-switch

Install the switch driver in your hub.
do not need Uninstall valve
Perform a driver Change in hub device driver menú.
delete memory caché if need

Delete the calce driver from your hub

Added to zigbee light Multifunction Mc

  - id: "IKEA/Bulb E26 opal"
    deviceLabel: IKEA Bulb
    manufacturer: IKEA of Sweden
    model: TRADFRI bulb E26 opal 1000lm
    deviceProfileName: switch-level

added to zigbee motion sensor Mc

  - id: "Third Reality/Motion 3RMS16BZ"
    deviceLabel: Third Reality Motion Sensor
    manufacturer: Third Reality, Inc
    model: 3RMS16BZ
    deviceProfileName: motion-battery

Neo coolcam is zwave device and I have notzwave drivers

Added to zigbee switch Mc

  - id: "SONOFF/01MINIZB"
    deviceLabel: SONOFF Switch
    manufacturer: SONOFF
    model: 01MINIZB
    deviceProfileName: single-switch

It is already added an test by @troy_owens and not wors for him.
Try you it

  - id: "TZ3000_hktqahrq/Switch"
    deviceLabel: TZ3000 Switch
    manufacturer: _TZ3000_hktqahrq
    model: TS0001

To all who write to me,
If I do not answer a post, it is not that I do not want to answer. Is that I will have forgotten :woozy_face:
Thanks

3 Likes

Thanks, I will try it later today day.

I used your driver on 3 eWeLink switches yesterday. 1 is set as bulb, 1 as plug and 1 as switch and it works good.

1 Like

The Sonoff Mini switch is pairing with a DTH, not your ZigBee Switch driver. I did it twice. Before the 2nd try I closed the app cleared cache, force stopped app, and rebooted hub.

I have not tried the Tuya switch.

That manufacturer makes zwave, Zigbee, and WiFi models, often using the same case so they look identical, but with different model numbers.

They have a Zigbee motion sensor and a Zigbee contact sensor, but I think the most current Zigbee models are rebranded tuya devices.

http://szneo.com/en/products/index.php?id=68

Wath DTH and is stock or custom?

Normally is due to device pairng with a custom dth or generic fingerprint.

I would have to add the generic fingerprint and then anyone who does not want to use the driver on some switch, would have to uninstall the switches paired to the driver and remove the driver.

If your switch paired with de DTH zigbe switch power stock, normally is due to device pairng with a generic fingerprint.
I would have to add the generic fingerprint to driver but then anyone who does not want to use the driver on some switch, would have to uninstall the switches paired to the driver and remove the driver.

In this case sent me, is a zwave model

1 Like