Good Morning. Mariano, you could add this zigbee siren from Heiman.
added to this driver version
┌─────────────┬──────────────────────────────────────┐
│ Name │ Zigbee Switch Mc │
│ Version │ 2021-12-20T14:05:51.000309 │
└─────────────┴──────────────────────────────────────┘
- id: "FeiBit/FNB56-ZSW01LX2.0"
deviceLabel: FeiBit Switch
manufacturer: FeiBit
model: FNB56-ZSW01LX2.0
deviceProfileName: single-switch
This Gledopto GL-C-008S RGBCCT Plus controller is already added. I am using it on Mariano’s driver
Added to this driver version
┌─────────────┬──────────────────────────────────────┐
│ Name │ Zigbee Multi Switch Zemismart Mc │
│ Version │ 2021-12-20T14:29:12.988116 │
└─────────────┴──────────────────────────────────────┘
- id: "Zemismart/TS011F"
deviceLabel: Lidl MultiPlug
manufacturer: _TZ3000_92qd4sqa
model: TS011F
deviceProfileName: two-outlet
I undertand that you refer to this model GL-B-008ZS
You can try this other driver.
It is the same as the other one but it has the added function of a transition time in the changes of level, color, off and on, with a time set in preferences.
By default they are set to 2 sec.
If you don’t want transition times you can put 0sec in preferences settings
┌─────────────┬────────────────────────────────────────┐
│ Name │ Zigbee Light Multifunction and Tr-Time │
│ Version │ 2021-12-20T11:26:21.661031 │
└─────────────┴────────────────────────────────────────┘
Hello,
I have no adapted siren driver
I have created a new profile smoke only, without battery.
I don’t know if it will work.
All devices paired to this driver, which is the official one, have the problem that they show status searching or no status in the tile, but they work well both with STHM or with individual alert.
Hope they fix it
┌─────────────┬──────────────────────────────────────┐
│ Name │ Zigbee Smoke Detector Mc │
│ Version │ 2021-12-20T14:50:13.739359 │
└─────────────┴──────────────────────────────────────┘
- id: "HEIMAN/GASSensor-EM"
deviceLabel: HEIMAN Gas Detector
manufacturer: HEIMAN
model: GASSensor-EM
deviceProfileName: smoke
I think I have not forgotten any, you will tell me
I have seen that in the Beta stock driver there is an American Heiman siren model.
I’ve added your fingerprints, see if it works
┌─────────────┬──────────────────────────────────────┐
│ Name │ Zigbee Siren Mc │
│ Version │ 2021-12-20T14:59:52.198228 │
└─────────────┴──────────────────────────────────────┘
- id : Heiman/WarningDevice-EF-3.0
deviceLabel : HEIMAN Siren
manufacturer : Heiman
model : WarningDevice-EF-3.0
deviceProfileName : switch-alarm
I think this one was missing
It worked very well. Thanks. Congratulations on the excellent job you are doing. It gave a new meaning to the ST
Would it be possible to create a drive for the ST water leak sensor? It uses the DHT SmartSense Moisture Sensor.
- zigbeeNodeType: SLEEPY_END_DEVICE
- firmwareManufacturerCode: 4673
- firmwareFullVersion: 00000014
- application: 14
- endpointId: 01
- firmwareImageType: 48
- manufacturer: Samjin
- model: water
01 0104 0402 00 07 0000 0001 0003 0020 0402 0500 0B05 02 0003 0019
I’ll look at it when I have a while.
You will have to try it, I don’t have a device
OK! I do the tests
Zigbee Smart Switch Zemismart (with consumption metering)
this is a 30A relay that has power measurement, real time and total consumption.
- application: 44
- endpointId: 01
- manufacturer: _TZ3000_f1bapcit
- model: TS011F
- zigbeeNodeType: ROUTER
01 0104 010A 01 09 0000 0003 0004 0005 0006 0702 0B04 E000 E001 02 0019 000A
this one was also missing from the ones I sent above
Try to see if it works and will add to driver list.
- It has temperature report settings in preferences since the most important thing should be to detect water losses.
The temperature is secondary and should not have precision by default so as not to drain the battery.
By default I have set 15 minutes of maximum interval and 0.5º of reportable temperature change.
You can choose the values you want within the range of preferences
If you see that it takes time to show the first temperature value, heat it by hand
┌─────────────┬──────────────────────────────────────┐
│ Name │ ST-Zigbee Moisture Sensor Mc │
│ Version │2021-12-20T16:24:51.69515 │
└─────────────┴──────────────────────────────────────┘
- id: "SmartThings-Moisture-Sensor"
deviceLabel: ST Water Sensor
manufacturer: Samjin
model: water
deviceProfileName: moisture-temp-battery
Added to this driver version
┌─────────────┬──────────────────────────────────────┐
│ Name │ Zigbee Switch Power Mc │
│ Version │ 2021-12-20T16:33:44.471572 │
└─────────────┴──────────────────────────────────────┘
- id: "Zemismart/Relay"
deviceLabel: Zemismart Relay
manufacturer: _TZ3000_f1bapcit
model: TS011F
deviceProfileName: switch-power-energy
Today I am not going to update any more drivers for the switch, switch power or light ,since every time I update version I am updating all the users who use it, it will not be that will create any problems due to so many continuous updates